Swisslog's Forum › Swisslog version 5.x › General discussion v
Night mare

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Night mare
10-02-2019, 10:20 AM,
#1
OZ4VW Offline
Member
***
 		Posts: 53
Threads: 15
Joined: Oct 2013
Reputation: 0
Night mare
Good morning
Have a failure on my PC Mother board
Hav set up a new machine with two old Disk in with all data
One new disk to with all Windows installation

It say # Jet engine not found" when I start SW up
How to redo this
Any input
Br Arne OZ4VW
Find
Reply
10-02-2019, 10:36 PM,
#2
EA3GCV Offline
Super Moderator
******
 		Posts: 1.682
Threads: 147
Joined: May 2013
Reputation: 12
RE: Night mare
Hello Arne,

I need more data to help you. Maybe your operating system is not well installed, or you have mot restored properly your database. But you should have any Jet Engine issue at all. Please install Swisslog using the installer then restore your Swisslog database. I guess you have done something wrong with it.

Please read this post regarding the files you need to restore: 

https://www.swisslogforwindows.com/forum...hp?tid=370

Best 73
Jordi, EA3GCV
Current developer of Swisslog
Find
Reply
10-02-2019, 11:20 PM,
#3
OZ4VW Offline
Member
***
 		Posts: 53
Threads: 15
Joined: Oct 2013
Reputation: 0
RE: Night mare
Hello Jorge
Try to restore tomorrow evening

Link you sent ended out blind
73 Arne
Find
Reply
10-02-2019, 11:42 PM,
#4
EA3GCV Offline
Super Moderator
******
 		Posts: 1.682
Threads: 147
Joined: May 2013
Reputation: 12
RE: Night mare
Hello Arnie,

The link is working properly here! Please refresh your browser cache or copy/paste the link into another web browser. If you still have problems, please let me know and I will send you the info to your e-mail address.

Best 73
Jordi, EA3GCV
Current developer of Swisslog
Find
Reply
11-02-2019, 04:46 PM,
#5
OK1DTM Offline
Junior Member
**
 		Posts: 21
Threads: 1
Joined: May 2013
Reputation: 0
RE: Night mare
(10-02-2019, 11:20 PM)OZ4VW Wrote: Hello Jorge
Try to restore tomorrow evening

Link you sent ended out blind
73 Arne

Here also is link broken (Firefox/Chrome) in Linux Result "The specified thread does not exist." Sad
Find
Reply
11-02-2019, 07:04 PM,
#6
OZ4VW Offline
Member
***
 		Posts: 53
Threads: 15
Joined: Oct 2013
Reputation: 0
RE: Night mare
Problem carry on
Have to reinstall a Hard Drive
Would try to install again but it point to a non existing Drive on my PC
UAC is removed but not able to point to correct place
Br Arne
Find
Reply
13-02-2019, 06:27 PM,
#7
OZ4VW Offline
Member
***
 		Posts: 53
Threads: 15
Joined: Oct 2013
Reputation: 0
RE: Night mare
Good evening

Any help out there
Have as far I thing done everything
Removed UAC as stated on homepage
Rebooted a lot of times
Removed install file and downloaded a new one
And all time I try to install it say I will do it on a decent HD as even not exist on my PC
A bit critical like to have my log running playing with radio instead of PC
Br Arne OZ4VW
Find
Reply
14-02-2019, 05:58 PM,
#8
EA3GCV Offline
Super Moderator
******
 		Posts: 1.682
Threads: 147
Joined: May 2013
Reputation: 12
RE: Night mare
Hello Arne,

First of all, is windows installed in drive C? Is windows working properly with no issues?

Could you install Swisslog in C:\Swisslog? (default folder) Is the Swisslog installation finished properly? Have you restore any previous backup? If so I recommend to first do a fresh Swisslog installation and perform a basic setup to ensure that everything is working properly. Afterwards try to restore the files explained in this post:

https://www.swisslogforwindows.com/forum...hp?tid=370

I have checked and this link works perfectly. Copy/paste in your web browser. Keep in mind that if you want to restore your old Swisslv5.ini file, and the old installation folder is not the same as the current one, you have to edit the Swisslv5.ini file with a text editor and replace the old path by the new path (you can use the Edit / Replace funtion of windows note editor).

In case you still have issues I can check online via Teamviewer what may happen. Please contact me via whatsapp to my phone +34656409020 to arrange a Teamviewer session.

Best 73
Jordi, EA3GCV
Current developer of Swisslog
Find
Reply
14-02-2019, 06:36 PM,
#9
OZ4VW Offline
Member
***
 		Posts: 53
Threads: 15
Joined: Oct 2013
Reputation: 0
RE: Night mare
Hello Jordi
Yes to most
New main C Hard disk
New installed with Win 10
Most seem to work Office / N1MM / LOTW ect

But not SW log
I download file
Run as Admin
Se the point UAC ( Set to 0 in controlpanel)
Choose langue
And then this is happen as shown in attached picture
And I have no chance to change letter and I have no F in my machine
Will install Teamwiev in few minutes
Br Arne
Find
Reply
14-02-2019, 06:37 PM,
#10
OZ4VW Offline
Member
***
 		Posts: 53
Threads: 15
Joined: Oct 2013
Reputation: 0
RE: Night mare
Hi
I can not open this link
Not even when I copy it
Br Arne
Find
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)